Peugeot 3008 Key Fob Problems
Peugeot's mid-sized 3008 SUV has lot going for it. It's stylish, handles well and has a surprisingly big boot. Can it compete in the most competitive segment of the market, perhaps?
If your Peugeot key fob is not functioning, it might have been exposed to clean tap water or soapy water. It is possible to remove the battery, then clean it with isopropyl ethanol or an electronic cleaner.
Dead coin battery
Peugeot key fobs are powered by an e-cigarette size battery. This power is used to operate the remote locking system and other functions. The battery is limited in lifespan and is susceptible to wear after a long period of usage. A simple method to determine whether the battery is defective is to perform the voltage test. Multimeters can be used to measure voltage between the plus and minus poles of the battery. The results of this test will reveal whether the battery is dead or not.
The receiver module may be the reason for your key fobs failing to function after you've used your Peugeot 3008 for a long period of time. The receiver module is responsible for receiving radio frequency signals transmitted through key fobs and sending them out to the car's systems. If the receiver module is faulty it won't be able to send commands to other modules inside the vehicle.
Another common reason for a key fob that is not working is moisture or sweat that has accumulated on the circuit board. It can trigger short circuits, which can draw the battery out and also disable the fob's remote locking function. If this is the case, you should bring your key fob in to a technician that specializes in chip level repairs.
Water damage
Water damage can be a problem, whether you dropped your keyfob in the swimming water, washed it, or left it out in the rain. Water is a great conductor, and can damage circuit boards. It can also cause corrosion to the metal connections on the key fob as well as other components. A wet circuit can cause a battery to lose its charge.
If you have an additional key fob, use it to lock or unlock the Peugeot 3008 to eliminate a dead coin-cell battery as the cause of the problem. Another issue that can stop the key fob from operating effectively is interference signals that interfere with the signal sent to the receiver module. These signals of interference can originate from a wide range of sources such as radio transmitters in close proximity.
If you hear sloshing sounds coming from your Peugeot 3008 when you drive this could be due to a clogged condensate drain from the evaporator. You can identify this by taking a look at the drain holes that are underneath your door and blowing compressed air through the drain holes. You can also use a flexible wire to wiggle the drain holes and clear any dirt that has collected there. Air pockets can be identified by sloshing sounds.
Faulty receiver module
The receiver module on the Peugeot 3008 key fob is responsible to transmit the remote keyless system signal from the key fob to the car's receiver. This module can be damaged and block the car from acknowledging your key fob. peugeot 3008 key could be caused by a dead battery or water damage. Also, interference from electronic devices operating on the same frequency. In these situations the car could display a message saying "card not detected" on the display.
There are many ways to fix this issue. You could try replacing the battery or reprogramming your key fob. You can also use a spare key to start the car. If the key fob does not work after following these steps, then it could have a faulty chip.
The best method to determine whether the key fob has a malfunctioning chip is to take it off and clean it with paper towel and rub alcohol. If the chip is fried it is recommended to purchase another one. The FB Series enclosures come with the battery holder for coins that can be used with the most commonly used types of key fob batteries. These enclosures can be customized with digital printing and CNC-machined cutouts. If your key fob was exposed to salty or dirty tap water, your chip may be contaminated and require to be cleaned.
Keyless entry systems with malfunctions
When you see the message "card not detected" this means that your vehicle is unable to receive signals from your key fob. This can be caused by many reasons, such as batteries that are weak or dead. Most of the time, the issue can be fixed by pressing the start button using the key fob. In some cases you may need to take the keyfob to a Peugeot dealer for further repairs.
Examining the battery is the first step in solving the issue with a Peugeot 3008 keyfob that won't lock or unlock doors. Batteries are the most frequent reason for a fob that is malfunctioning however there are a variety of other factors that contribute to this issue too. These include worn buttons and water damage.
If you've recently been exposed to water and have your Peugeot key fob exposed to pure tap water, it's a good idea remove the battery and dry the electronic components using paper towel. You can also make use of a cleaner or isopropyl ethanol to do this. It's best to change the fob if it has been exposed to salt water or soapy water.
If your key fob still not working, try to reset it by disconnection of the 12 volt battery for approximately 15 minutes. Then reconnect the negative cable first, followed by the positive cable.